ppm-series ? ppm03-s-xxelf ? single output - plasti c case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 1/3 ppm 03-s-xxelf all specifications typical at ta=25c, nominal inpu t voltage and full load unless otherwise specified input specifications input voltage range 85 ? 264 vac or 110 ? 370 vdc universal input frequency 47 ? 440 hz input (inrush) current ppm03 models 110 vac 230 vac 65 ma (10a), typ. 30ma (20a), typ. external input fuse (recommended) 0.5a / 250v slow blow output specifications voltage accuracy 2%, typ (3% @3.3 vout) input variation 0.5% load variation (10-100%) 1% ripple and noise (20mhz bandwidth) 60mv pk-pk short circuit protection continuous, auto recovery over output voltage protection chip lock up common specifications temperature range -25c to +70 c power derating 2% / c case temperature +95c (max) storage -40c to +105 c hold up time 50ms, typ. (230vac) humidity (non condensing) 95%, max. temperature coefficient 0.02%/c (main output) switching frequency 100khz i/o isolation voltage 3000vac / 1min. leakage current none emi / rfi conducted en55022, level a emc compliance esd rf eft / bursts surge iec/en 61000-4-2 level 4 8kv/15kv iec/en 61000-4-3 iec/en 61000-4-4 level 3 iec/en 61000-4-5 level 3 1kv/2kv safety standarts iec60950, en60950, ul60950 safety approvals en60950, ul60950 safety class class 2 case material ul94v-0 rated reliability calculated mtbf (mil-hdbk-217f) > 300,000 hrs weight ~ 40g mainzer stra?e 151?153 d-55299 nackenheim tel. +49 6135 7026-0 fax: +49 6135 931070 www.peak-electronics.de peak@peak-electronics.de the ppm series are high efficiency green power moduls with various packaging provided by peak. the features of this se ries are: wide input voltage, dc and ac all in one, high efficiency, hig h reliability, low loss, safety isolation etc. they are widely used in indus trial, office and civil equipments. emc and safety standards meet internati onal standards iec61000 ul60950 and iec60950, and multicertificat e is in processing. ppm-series 3 watt univ. 85-264vac (110-370vdc) single output over voltage protection (out) 3 kv ac i/o isolation low ripple and noise high efficiency rev.05-2011
ppm-series ? ppm03-s-xxelf ? single output - plasti c case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 2/3 selection guide single output order # p o w e r ( w ) o u t p u t v o l t a g e ( v d c ) o u t p u t c u r r e n t f u l l l o a d ( m a ) e f f i c i e n c y ( % ) single output ppm03-s-3r3elf 2.3 3.3 700 63 ppm03-s-05elf 3 5 600 72 PPM03-S-09ELF 3 9 330 74 ppm03-s-12elf 3 12 250 76 ppm03-s-15elf 3 15 200 76 ppm03-s-24elf 3 24 125 78 if you need other specifications, please enquire. package / pinning / derating 17.78 (0.70) 23.00 (0.91) 0.8 (0.03) # single 1 ac (l) 3 ac (n) 13 n.c. 14 - vout 16 +vout 22 +vin (dc) 23 - vin (dc) pin connections -25 -10 0 55 70 100 80 60 40 20 l o a d ( % ) temperature(c)
ppm-series ? ppm03-s-xxelf ? single output - plasti c case specification can change without a notice ? we acce pt no liability for any inaccuracy or printing erro rs. page 3/3 app notes: +v0 -v0 l n mov 22 26 + + *fuse *ntc ln c3 c1 c2 tvs rl +v0 -v0 l n mov nf c8 c6 c7 + + 22 26 *fuse *ntc l n c3 c1 c2 tvs rl ppm03 emc application figure external capacitors typical value(unit: ? f) model c1 c2 c3 tvs ppm03s3r3elf 150 0.1 4.7/400v p4ke6.8a ppm03s05elf 150 0.1 4.7/400v p4ke6.8a ppm03s09elf 120 0.1 4.7/400v p4ke12a ppm03s12elf 120 0.1 4.7/400v p4ke20a ppm03s15elf 120 0.1 4.7/400v p4ke20a ppm03s24elf 68 0.1 4.7/400v p4ke30a note: 1. output filtering capacitors c1, c3 is electrolytic capacitors, it is recommended to use high frequency and low impedance electrolytic capacitors. for capacitance and curren t of capacitor please refer to manufactures datash eet. voltage derating of capacitor should be 80% or above. c2 is ceramic capacitor, it is used to filter high frequency nois e. tvs is a recommended component to protect postcircuits (if converter fails). 2. mov is required to ppm03 models to protect the d evice under surge. 3. it is recommended to connect fuse 4. if emc performance is required, recommended to a dd emc filter at the input end (see figures) c6: x capacitor, recommended parameter 0.1 f/275v; c7,c8: y capacitor, recommended parameter 2 200pf/400v; nf: common model choke, recommended inducta nce is about 10mh30mh. 5. ppm03 models: terminals 22 and 26 are internal r ectification and filtering terminals. to protect th e models further, it is recommended to connect an electrolytic capacitor c3 (it is recommended to be 4.7f/400v). if operation voltage of the module is between 160~264vac, c3 can be removed.
|
